Heat Transfer Calculations

Myer Kutz

Heat Transfer Calculations

買這商品的人也買了...

相關主題

商品描述

Description

Packed with laws, formulas, calculations solutions, enhancement techniques and rules of thumb, this practical manual offers fast, accurate solutions to the heat transfer problems mechanical engineers face everyday

Table of Contents

CONTRIBUTORS

PREFACE

Part 1 - Introductory Calculations

Chapter 1: Multiphase Films and Phase Change

Chapter 2: Industrial Heat-Transfer Calculations

Part 2 - Steady-State Calculations

Chapter 3: Heat Transfer and Temperature Results for a Moving Sheet Situated in a Moving Fluid

Chapter 4: Solution for the Heat-Transfer Design of a Cooled Gas Turbine Airfoil

Chapter 5: Steady-State Heat-Transfer Sample Problem: Cooling Fin

Chapter 6: Cooling of a Fuel Cell

Chapter 7: Turbogenerator Rotor Cooling Calculation

Chapter 8: Heat Transfer through a Double Glazed Window

Part 3 - Transient and Cyclic Calculations

Chapter 9: On the Use of Green's Function to Solve for Temperatures in a Bi-Material Slab Exposed to a Periodic Heat Flux Applied to Corrosion Detection

Chapter 10: Lumped Capacitance Model of a Tube Heated by a Periodic Source with Application to a Pulsed Detonation Engine Tube

Chapter 11: Calculation of Decoking Intervals for Direct-Fired Gas and Liquid Cracking Heaters

Chapter 12: Transient Heat-Transfer Sample Problem: Tape Pack Cooling

Chapter 13: Calculation of the Transient Response of a Roof to Diurnal Heat Load Variations

Chapter 14: Transient Heating of a Painted Vehicle Body Panel in an Automobile Assembly Plant Paint Shop Oven

Chapter 15: Thermal System Transient Response

Chapter 16: Thermal Response of Laminates to Cyclic Heat Input from the Edge

Chapter 17: A Simple Calculation Procedure for Transient Heat and Mass Transfer with Phase Change: Moist Air Example

Chapter 18: A Calculation Procedure for First and Second Law Efficiency Optimization of Refrigeration Cycles

Chapter 19: Transient Analysis of a Low-Temperature, Low-Energy Carrier, LoTEC(c)

Chapter 20: Parameter Estimation of LoTEC(c)

Part 4 - Heat-Transfer Coefficient Determination

Chapter 21: Calculation of Convective Heat-Transfer Coefficient using the Semi-Infinite Solid Assumption

Chapter 22: Determination of Heat-Transfer Film Coefficients by the Wilson Analysis

Part 5 - Tubes, Pipes, and Ducts

Chapter 23: Calculation of Local Inside-Wall Convective Heat-Transfer Parameters from Measurements of the Local Outside-Wall Temperatures along an Electrically Heated Circular Tube

Chapter 24: Two-Phase Pressure Drop in Pipes

Chapter 25: Heat-Transfer Calculations for Predicting Solids Deposition in Pipeline Transportation of "Waxy" Crude Oils

Chapter 26: Heat Transfer in a Circular Duct

Part 6 - Heat Exchangers

Chapter 27: Air Cooling of a High-Voltage Power Supply Using a Compact Heat Exchanger

Chapter 28: Energy Recovery from an Industrial Clothes Dryer Using a Condensing Heat Exchanger

Chapter 29: Sizing of a Crossflow Compact Heat Exchanger

Chapter 30: Single-Phase Natural Circulation Loops: An Analysis Methodology with an Example (Numerical) Calculation for an Air-Cooled Heat Exchanger

Chapter 31: Evaluation of Condensation Heat Transfer in a Vertical Tube Heat Exchanger

Chapter 32: Heat Exchanger Design Using an Evolutionary Algorithm

Part 7 - Fluidized Beds

Chapter 33: Fluidized Bed Heat Transfer

Part 8 - Parameter and Boundary Estimation

Chapter 34: Estimation of Parameters in Models

Chapter 35: Upper Bounds of Heat Transfer from Boxes

Chapter 36: Estimating Freezing Time of Foods

Part 9 - Temperature Control

Chapter 37: Precision Temperature Control Using a Thermoelectric Module

Thermal Analysis and Design

Chapter 38: Thermal Analysis of a Large Telescope Mirror

Chapter 39: Thermal Design and Operation of a Portable PCM Cooler

Chapter 40: A First-Order Thermal Analysis of Balloon-Borne Air-Cooled Electronics

Chapter 41: Thermal Analysis of Convectively Cooled Heat Dissipating Components on Printed Circuit Boards

Chapter 42: Design of a Fusion Bonding Process for Fabricating Thermoplastic-Matrix Composites

Part 11 - Economic Optimization

Chapter 43: Economic Optimization of Heat-Transfer Systems

Chapter 44: Turkey Oven Design Problem

INDEX

商品描述(中文翻譯)

描述

這本實用手冊充滿了法律、公式、計算解決方案、增強技術和經驗法則，為機械工程師每天面臨的熱傳遞問題提供快速準確的解決方案。

目錄

貢獻者
前言
第一部分 - 入門計算
第1章：多相薄膜和相變
第2章：工業熱傳遞計算
第二部分 - 穩態計算
第3章：移動流體中移動片材的熱傳遞和溫度結果
第4章：冷卻燃氣渦輪機葉片的熱傳遞設計解決方案
第5章：穩態熱傳遞樣本問題：冷卻散熱片
第6章：燃料電池的冷卻
第7章：渦輪發電機轉子冷卻計算
第8章：雙層玻璃窗的熱傳遞
第三部分 - 瞬態和循環計算
第9章：使用格林函數求解受週期性熱通量作用下的雙材料板的溫度問題
第10章：受週期性源加熱的管道的總容量模型計算，並應用於脈沖爆震發動機管道
第11章：直燃式氣體和液體裂化加熱器的脫碳間隔計算
第12章：瞬態熱傳遞樣本問題：帶狀包裝冷卻
第13章：屋頂對日變熱負載變化的瞬態響應計算
第14章：汽車裝配廠噴漆車身板的瞬態加熱
第15章：熱系統瞬態響應
第16章：層壓板對邊緣循環熱輸入的熱響應
第17章：相變的瞬態熱傳和質量傳遞的簡單計算程序：濕空氣示例
第18章：制冷循環的第一和第二定律效率優化的計算程序
第19章：低溫、低能量載體LoTEC(c)的瞬態分析
第20章：LoTEC(c)的參數估計
第四部分 - 熱傳遞系數確定
第21章：使用半無限固體假設計算對流熱傳遞系數
第22章：使用威爾遜分析確定熱傳遞膜系數
第五部分 - 管道和管道
第23章：從電加熱圓管沿外壁局部溫度測量計算內壁局部對流熱傳遞參數
第24章：管道中的兩相壓降
第25章：預測'蠟質'原油管道運輸中固體沉積的熱傳遞計算
第26章：圓形管道中的熱傳遞
第六部分 - 熱交換器
第27章：使用緊湊型熱交換器對高壓電源進行空氣冷卻
第28章：使用冷凝熱交換器對工業烘乾機進行能量回收
第29章：緊湊型交流熱交換器的尺寸確定
第30章：單相自然循環迴路：一種分析方法，以及一個空氣冷卻熱交換器的數值計算示例
第31章：垂直管道熱交換器中冷凝熱傳的評估
第32章：使用演化算法進行熱交換器設計
第七部分 - 流化床
第33章：流化床熱傳遞

類似商品